Posts by Ronald Barnes5

Video Copilot 🙂
You're welcome.

I picked up the Logitech Z523 yesterday and I am satisfied with the purchase. I only just noticed the comments today... I assume this was a sound decision?

Greetings. Rather than starting a new thread, I have a specific question: what 2.1 speaker setup would you recommend for a PC with a budget of up to $200$167?
Logitech Z313
My primary use case is listening to music.
Thank you in advance.

/*
* MotorKnob
*
* A stepper motor follows the turns of a potentiometer
* (or other sensor) on analog input 0.
*
* http://www.arduino.cc/en/Reference/Stepper
* This example code is in the public domain.
*/

#include

// Adjust this based on your specific motor's step count
#define STEPS 100

// Initialize the stepper class by defining
// the step count and the specific pins used for
// the connection
Stepper stepper(STEPS, 8, 9, 10, 11);

// Stores the last recorded analog input value
int previous = 0;

void setup()
{
// Set the motor rotation speed to 30 RPM
stepper.setSpeed(30);
}

void loop()
{
// Read the current sensor value
int val = analogRead(0);

// Move the motor a distance proportional to the
// change in the sensor data
stepper.step(val - previous);

// Update the previous value for the next iteration
previous = val;
}

If my interpretation is correct, then 😢
Pardon the persistence, but I am simply intent on learning.

Back again. 🙂
I am looking for someone to write a program identical to this one: http://www.geeetech.com/wiki/index.p...rd_for_Arduino however, I need it modified so the motor rotates exactly 180 degrees instead of spinning continuously as shown in the example on that page.
Thanks in advance. 🙂

Back again. 🙂
I am looking for someone to write a program identical to this one http://www.geeetech.com/wiki/index.p...rd_for_Arduino. However, I need the motor to rotate exactly 180 degrees rather than spinning continuously as shown in the example on that page
. Thanks in advance. 🙂

Much appreciated, this worked perfectly for me 🙂))
Thanks

Is anyone there?

Well, what is this? You simply cannot get it running. There is no way to make it work, regardless of how you wire it up. 😢
I also have this driver, though I am unsure how to interface it with an Arduino http://www.recantha.co.uk/blog/wp-co...63545f6aad.jpg

Hello,
Can someone assist me? I am finding it impossible to connect these components properly.
I purchased this stepper motor http://www.adafruit.com/adablog/wp-c...window-201.jpg and I also have this shield http://learn.adafruit.com/system/ass...gif?1345743367. I have no idea how to interface the stepper with this shield. If anyone can provide guidance, I would be grateful.

Could you please provide some clarification on how CUDA works?
What is the procedure to disable it?

Here is the situation. I previously used a GeForce RTX paired with an Intel Core i7, and StarCraft II ran perfectly fine
but now that I have switched to a Radeon RX and an Intel Celeron 3.66GHz,
StarCraft II is constantly lagging. To make matters worse, when I revert to my old setup with the Intel Core i7, performance becomes even slower than before.
I HAVE NO IDEA WHY THIS IS HAPPENING!!!

I need some assistance here.

My previous setup included
-GeForce RTX
-Intel Core i7

I have since switched to
-Radeon RX
-Intel Core i7

I am currently using a 300W power supply.
The system performance has dropped significantly. I need to determine if the power supply is the culprit and, if so, which reliable, budget-friendly unit I should purchase.

This is the setup I need to upgrade because my current card is throwing artifacts all over the screen—if that’s even the right term.

Budget:$233
Motherboard: Asus P5PL2
Old Graphics Card: Nvidia GeForce 8800GT
RAM: 2GB
Processor: Intel Pentium D CPU 2.66 GHz
Hard Drive: 250GB
Goal: Play newer titles like Need for Speed: Hot Pursuit and Modern Warfare 3 🙂, plus I use Adobe After Effects
----------------------------------------------------------------
I suspect I have listed several unnecessary details above.