PC Modding

Edward Peterson70 said:I've got Firewire right there on my motherboard and I'm dying to hook something up, but I just can't seem to get it working...

Wait, have you actually heard of the Firewire Bracket? It’s a total lifesaver if you're stuck in this situation! 🙂

http://estore.asus.com/images/A8N32-...-011000061.jpg

wiredmarlin5 said:Wait, you haven't heard about the Firewire Bracket? 🙂

http://estore.asus.com/images/A8N32-...-011000061.jpg

Mr. Moderator (😍), yes I have

By the way, what kind of point is that even supposed to make if my motherboard already has Firewire built-in? 😂

Well, I didn't quite catch that you already had one in the back, though I honestly can't wrap my head around why you'd bother putting one in the front if the rear is already occupied... Are you just feeling a little lazy today? I mean, the space in the front is sitting there completely empty just because you're working with a subpar, budget case😁

wiredmarlin5 said:I didn't realize you had it positioned behind you. I just don't see why you'd want it in front if it's already behind you.

Well, the PC is tucked away in the corner. My desk is pretty large, and I find myself having to brace my elbow against the table just to reach the front panel ports.
I'm curious to hear how everyone else handles their setup, since I wasn't the one who picked out this case or handled the component layout.

Edward Peterson70 said:The upper plastic section is way too smooth, so when you're gaming and your hands start sweating, your fingers just slide right off.
I actually tried to fix this by taping some electrical tape over it, and I have to say, besides the aesthetic downgrade, 😂 it actually improved the usability.

Now, let's talk about how much sense that makes... imagine waiting for those 95°F summer days when you're gripping that mouse and sweat is literally pouring off your palms. That electrical tape is going to heat up and turn into a sticky, gummy mess, attracting every bit of dust in the room. Then you'll be scrubbing at it, peeling the tape off, starting all over again... what a headache.

Joseph Carter9 said:I'm not sure how practical that really is... once those summer days hit 95°F and you're just sitting there, sweat starts dripping off your hands, the grip gets hot, and then it starts getting all tacky. Then dust settles on the sticky surface, so you have to wipe it off, strip the grip, and start the whole process over again...

I've been doing some light browsing lately... 🙂

The big question is: which mouse should I settle on before summer arrives? ☕

@Edward Peterson70/">@@Edward Peterson70
You just have to pull the entire faceplate out and hold it steady with those little plastic clips—I can't even remember the technical term for them, honestly
—and there aren't any actual screws involved, though you will eventually have to unscrew that silver trim piece
running along the front, along with the USB ports and the headphone and mic jacks.
As for the FireWire situation, I suppose you could just find a way to screw or glue it onto the front somewhere.
Just grab a mounting bracket, take it apart, and screw it right on the front panel.
It’s really just a matter of having a bit of willpower and putting in some elbow grease 😉

steelsailor3 said:@Edward Peterson70/">@@Edward Peterson70
You just need to pull the entire faceplate off; it’s held in place by those plastic clips (I can't recall the exact term),
there aren't any actual screws involved, though you will have to unscrew that silver trim piece
on the front, along with the USB ports and the headphone/mic jacks.
As for the FireWire port, you could probably find a way to screw or glue it onto the front.
Just buy a bracket, take it apart, and mount it up front.
It just takes a little bit of effort and patience. 😉

Thanks. It seemed strange to me why there was a cutout provided when nothing was actually on the PCB. 🤷

And I can definitely handle this DIY fix without any issues. 😉

When you're ready to pull that mask off, just grab it from the bottom edge—there’s plenty of room right there to get a good grip and tug it away.

steelsailor3 said:When you go to take the mask off, just grab it from the bottom edge; there's plenty of room there to get a good grip and pull it away.

That opening is actually meant for a 120mm fan located by the drive cage to help draw air in.
I actually sanded that part down to make the hole larger, which improved the airflow and helped quiet things down a bit.

I know, but honestly, it’s actually pretty convenient when you need to pop the cover off

Just so we're clear, if you end up ripping something apart while doing this, I'm officially washing my hands of any responsibility 😬

steelsailor3 said:I'm aware, but it's actually quite convenient for when you need to take the mask off.

Just a quick disclaimer: if you end up tearing anything while doing this, I can't be held responsible. 😬

I gave it a little try...
It’s not particularly loose. In fact, there isn't even a millimeter of movement.

Edward Peterson70 said:I gave it a little tug...
It’s not exactly loose. Honestly, it hasn't budged even a millimeter.

Check the inside to see if those plastic clips are visible. I remember trying to install a DVD drive in an old desktop once and pulling so hard I was certain the whole chassis was going to snap... but it held up.
You just need to apply a bit more muscle.

Honestly, you don't need to stress about it snapping. I've pulled mine off more times than I can count, and even though I was convinced it was going to crack every single time, it’s held up just fine.
Who would've guessed that Microsoft would actually put this much quality into their stuff? 😂

Look, just pull on it as hard as you can, and right before it snaps, it should pop out. 😬

steelsailor3 said:I'm disclaiming any and all responsibility for whatever gets torn in the process.[/COLOR]

Joseph Carter9 said:Basically, just pull as hard as you can, and it should pop right out just before anything snaps. 😬

In the meantime, I've already managed to take it off three times without tearing anything.

See? I told you we were right all along. 😛

I didn't even suspect 😉

I have implemented several modifications to the chassis, so please review my progress here:

1.
2.

Raymond Hernandez14 said:So, I decided to mess around with some PC Modding on my case—check out what I did:

1.
2.

Honestly, though, the most important stuff is the stuff you can't even see—you just gotta feel it in your soul. 🤣